Custom Men's Jet Black Metal-Free Tanned Leather Reefer Jacket with Hazard Applique
Custom Men's Jet Black Metal-Free Tanned Leather Reefer Jacket with Hazard Applique
Custom Men's Jet Black Metal-Free Tanned Leather Reefer Jacket with Hazard Applique
Model
Q4-071

Review

Description

Custom Men's Jet Black Metal-Free Tanned Leather Reefer Jacket with Hazard Applique

  • Material: metal-free tanned leather at roughly RGB 36, 36, 37, a cool near-black with a natural matte face and the grain and creases left visible.
  • Craft: flat leather applique with satin edging, chain-stitch hazard lines and chenille inside the lettering only, held by small silver studs.
  • Cut: deep rust red wide lapel, double-breasted four-button front, cream placket strip, two slanted waist pockets, straight hem, no belt.
  • Wear: cold-weather city wear over knitwear, gallery and studio days, and a clean black layer for evening.
  • Order: custom made to order in your measurements, colourway and label, with sampling and quantity pricing for larger runs.

Reefer Jacket in Jet Black Metal-Free Tanned Leather

A jet black metal-free tanned leather reefer jacket cut on a wide deep rust red lapel and a double-breasted four-button front, with a hazard warning structure layered down the back.

The body is metal-free tanned leather, a hide tanned without chromium or other metal agents so no metal residue sits in the skin. It comes up as a natural matte, soft-hand uniform grain: the surface carries no heavy coating and no high-gloss press, so a fingertip runs over a supple matte face with an even, fine grain while the natural creases stay visible at the edge rather than being flattened into a dead panel. Jet Black here is the measured colour at roughly RGB 36, 36, 37, a cool near-black that is neither a greyed charcoal nor a brownish old black; it stays deep and clean in daylight and holds in warm interior light without going grey. Front and back are cut from the same batch and drum and measured to match, so the large black ground reads as one continuous surface with no front-to-back break. Hide type, thickness, hand, colour and surface finish can all be specified against a swatch and shade card.

Custom Men's Jet Black Metal-Free Tanned Leather Reefer Jacket with Hazard Applique — custom size sheet and construction detail

Applique and finishing

Applique leads throughout. On the right chest the warning triangle, and on the back the hazard stripe band, the CAUTION block, the large warning triangle, the ARMORWOOD wordmark, the folded ribbon and the mirrored small triangles are all separately cut flat leather pieces with a smooth face, visible grain and a crisp cut edge, edged in satin stitch with a few detail lines. Chenille fills only the inside of the ARMORWOOD strokes, and chain-stitch draws the upper and lower edges of the stripe band plus the inner lines of CAUTION. A row of small silver studs runs along the yoke edge, front and back, and the faceted abstraction inside each triangle is a deep rust red bar over a dot rather than any lettering. There is no rhinestone, crystal or sequin anywhere, no backing plate under any shape, and no enclosing frame or ring around the triangles.

Custom Men's Jet Black Metal-Free Tanned Leather Reefer Jacket with Hazard Applique — applique and finishing detail

Cut and finish

The silhouette is a reefer jacket: a wide deep rust red leather lapel that runs continuously around the neck, a double-breasted front of four metal buttons in two rows of two, a cream placket strip, two slanted waist pockets, cream leather cuff bands and a straight hem at the hip, square through the body with sleeves to the wrist. The double-breasted front and the cream placket strip are front only; the back carries no button row and no placket. A cream leather yoke crosses the chest and continues over both shoulders at the same height on the back, finished with a fine charcoal satin line and the stud row along its lower edge, and a bone satin piping strip closes the shoulder seam. There is no belt. Length, sleeve, chest ease, lapel width, button count and position, pocket placement and cuff treatment are all built to your specification.

Specifications

MaterialJet Black metal-free tanned leather
StyleReefer Jacket
CraftLeather applique with chenille lettering, chain-stitch lines, satin edging and silver studs
ColorJet Black, deep rust red, cream
CollarDeep rust red wide leather lapel
ClosureDouble-breasted, four metal buttons, front only
Order TypeCustom made to order

Who it is for

For menswear buyers, boutique owners and private-label brands looking for a made-to-order jet black reefer jacket with applique work.

Care notes

  • Wipe with a soft dry cloth; keep away from prolonged direct sunlight and direct heat.
  • Do not machine wash or tumble dry; professional leather cleaning only.
  • Shipping and delivery times are confirmed per order — contact us for your destination.